Addressable Loop Mimic LED PCB (Slave) – ZPCB2252-MSL

The ZPCB2252-MSL is the slave PCB which has no loop interface to the CIE but is directly controlled by the ZPCB2252-MML board. Up to 7 slave boards can be daisy chained to the master board and each slave has 32 LED outputs allowing the number of LED outputs to be expanded up to a maximum of 250 (not all LEDs on the 7th slave are used). The power to these additional LEDs is also from the external power supply but is transferred through the interlinking cable between boards.

Cause and effect programming can be uploaded via the RS232 port to the master board to program how the LEDs will react to command/status information received from the CIE. This allows the LEDs to not only be used to show fire information but also faults, and can be configured to trigger by Zone, Panel, Loop or Address.
These boards are typically used for providing visual indications for fire or fault conditions on a site plan overlay.

Additional information
Order Code

ZPCB2252-MSL

System

Addressable

Product Type

Control Panels: Spare Parts

Contact me about this Product
Name
Email
Phone
Enquiry

SIMPLE SET-UP

Easy configuration with Eaton site installer

VARIANTS

2 versions available

INSTALLATION

Quick and easy to install

Two board types. Two powerful ways to make your system even more intelligent.

LED for clear indication of fire or fault location

LED boards will light up to indicate a fire or fault status, giving clear indication of the location of the fire or fault.

Relay output for connecting to other life saving systems

Relay boards have the ability to switch on other outputs such as lighting, door release mechanisms or sprinkler systems if a fault or fire is indicated

Outputs can be operated by address, zone or panel activation

The flexibility of these boards is further enhanced with each output having the ability to be programmed for fire or fault, with up to 5 different zones or addresses per output. If a device connected to the panel went into fault, the LED would indicate this enabling maintenance crew to easily locate the device and replace it.

Ideal for geographical LED mimic displays

Mimic boards provide clear indication of where an emergency is situated, helping building staff or emergency services act accordingly. The LED outputs provided by the PCB can be collected and used to build a separate mimic panel for building employees, or for fire services. The panel would consist of a basic schematic of the building or the floor of a building with up to 250 LEDs per master board.

Features and Benefits

• Available as master or slave, each has 32 outputs
• 250 outputs (1 master and 7 slaves)
• Ideal for mimic panel provision
• Each output can be programmed as fire or fault
• Each output can be operated by address, zone or panel
activation
• 2 versions available:
– LED
– Relay output
• Soft addressed
• Built in short circuit isolation
• Simple configuration using Cooper site installer
• Easy to install

Mimic LED PCB (Master)ZPCB2252-MML
Mimic Relay PCB (Master)ZPCB2252-MMR
Mimic LED PCB (Slave)ZPCB2252-MSL
Mimic Relay PCB (Slave)ZPCB2252-MSR

 

Quiescent Current:310mA
Operating Loop Voltage:18Vdc to 30Vdc
Inputs:4mA to 20mA
External PSU:15Vdc to 30Vdc
Voltage:24Vdc to 30Vdc
Current:10mA
Humidity (Non-condensing):0 to 95% RH
Dimensions (HxW):10mm x 290mm
Weight:0.25Kg
Suitable for use with:Eaton Addressable Fire Systems

DOWNLOADS

Success Stories

Look to the future, trust our past. Discover success stories and building references for Eaton’s Fire Detection Systems and Emergency Lighting products.

TEL: 254-774-211313

close
Start typing to see posts you are looking for.
Set your categories menu in Theme Settings -> Header -> Menu -> Mobile menu (categories)

Shopping cart

close
Scroll To Top